AEA Slip-on pipe flanges actually slide over the pipe. They are typically machined with an inside diameter slightly larger than the outside diameter of the pipe. This allows the flange to slide over the pipe but to still have a somewhat snug fit. Slip-ons are secured to the pipe with a fillet weld at the top and the bottom of the flange. These are further catagorized as a ring or a hub. Rings and hubs are both considered slip on flanges because they both fit over the pipe.
Flange Type:
Weld Neck, Slip On, Blind, Plate, Thread, Socket Weld, Lap Joint, Ring Joint, Orifice Flange, Spectacle Blind, Paddle Spacer and Blank Flange, Figure 8 Flange, etc;
Face: Raised Face (RF),Flat Face(FF), Ring Joint (RTJ)
Material:
Carbon Steel: Q235,20#,A105, ST37.2,C22.8, S235JR,P250GH,A350 LF1,LF2 CL1/CL2 LF3 CL1/CL2, ASTM A694 F42,F46,F48,F50,F52,F56,F60,F65,F70
Stainless Steel: A182 F304/304L, F316/316L, F316H,F316Ti,F321,F44(UNS S31254)
Ally Steel: A182 F1,F5/a,F9,F11,F12,F22,F91
Duplex Steel: A182 F51/UNS S31803,F53/UNS S32750 F55/UNS S3260
Special Alloy: ,C95400,C95500,C95800,Monel400,Inconel 600, Inconel 625, Inconel 800, Inconel 825
Standard:
ASME: ANSI/ASME B 16.5,ASME B16.36,ASME B16.47 Series A(MSS SP-44);ASME B16.47 Series B(API 605),AWWA C207
DIN: Plate(DIN2573,2576,2502),Blind(DIN2527),Loose(DIN2641-2676),Welding-Neck (DIN2627-2638), Threaded (DIN2565 2566 2567) ,Slip-On (DIN86029 86030)
EN: EN1092-1
JIS: JIS B2220
UNI: UNI2253-2278,UNI6083,UNI6084,UNI2280,UNI2281-2286, UNI6091-6097
GOST: GOST12820-80, GOST12821-80
BS: BS 4504,BS10-1962,BS3293-1960
Pressure:
ANSI:Class 75, Class 150, Class 300, Class 600, Class 900, Class 1500, Class 2500
DIN:PN 6,PN 10,PN 16,PN 25,PN 40
EN:PN 6,PN 10,PN 16,PN 25,PN 40
JIS:1K,2K,5K,10K,16K,20K,30K,40K,63K ;
GOST:PN 6,PN 10,PN 16,PN 25,PN 40,PN63,PN100,PN160
BS:TABLE D E
Machining Tolerance: From 0.005mm-0.01mm-0.1mm As Standard.
Machined Surface Quality: Ra 0.8-Ra3.2 according to customer requirements
Production Process:
Forging-Heat Treatment-Machining (rough machining and finish machining)-Drilling-Inspect-Stamp-Packing
Heat Treatment: Solution, N+T (Normalizing + Tempering), Q+T (Quenching + Tempering)
Surface Treatment
Anti-rust Oil, Transparent/Yellow/Black Anti-rust Paint,Zinc,Hot dipped Galvanized.
Usage:
Oil Field, Offshore, Water System, Shipbuilding, Natural Gas, Electric Power, Pipe Projects etc.
| RAW MATERIAL LIST | |||||
| NO. | Material Grade | Category | NO. | Material Grade | Category |
| A.Cr-Mo Alloy | C.Duplex | ||||
| 1 | ASTM A182 F1 | Cr-Mo Alloy | 27 | ASTM A182 F44 | Duplex SS |
| 2 | ASTM A182 F5 | Cr-Mo Alloy | 28 | EN10222 1.4462 | Duplex SS |
| 3 | ASTM A182 F9 | Cr-Mo Alloy | D.Stainless Steel | ||
| 4 | ASTM A182 F11 | Cr-Mo Alloy | 29 | ASTM A182 F304/F304L | Austenitic SS |
| 5 | ASTM A182 F22 | Cr-Mo Alloy | 30 | ASTM A182 F304H | Austenitic SS |
| 6 | ASTM A182 F91 | Cr-Mo Alloy | 31 | ASTM A182 F316/316L | Austenitic SS |
| 7 | EN10222-2 16Mo3 | Cr-Mo Alloy | 32 | ASTM A182 F317/317L | Austenitic SS |
| 8 | EN10222-2 13CrMo4-5 | Cr-Mo Alloy | 33 | ASTM A182 F316Ti | Austenitic SS |
| B.Carbon Steel | 34 | ASTM A182 F321 | Austenitic SS | ||
| 9 | ASTM A105 | Carbon Steel | 35 | ASTM A182 F347/F347H | Austenitic SS |
| 10 | ASTM A694 F52 | Carbon Steel | 36 | ASTM A182 F904L | Super Austenitic SS |
| 11 | ASTM A694 F60 | Carbon Steel | 37 | ASTM A182 F347/F347H | Austenitic SS |
| 12 | ASTM A694 F65 | Carbon Steel | 38 | EN10222-2 1.4306 | Austenitic SS |
| 13 | ASTM A694 F70 | Carbon Steel | 39 | EN10222-2 1.4401 | Austenitic SS |
| 14 | ASTM A516 GR 65 | Carbon Steel | 40 | EN10222 1.4404 | Austenitic SS |
| 15 | ASTM A516 GR 70 | Carbon Steel | 41 | EN10222 1.4541 | Austenitic SS |
| 16 | EN10222-2 S235JRG2 | Carbon Steel | 42 | EN10222 1.4571 | Austenitic SS |
| 17 | EN10222-2 P250GH | Carbon Steel | 43 | EN10222 1.4539 | Super Austenitic SS |
| 18 | EN10222-2 P280GH | Carbon Steel | Alloy | ||
| 19 | EN10222-2 P355QH | Carbon Steel | 44 | B564 UNS N08020 | Ni-Alloy |
| 20 | ASTM A516 GR 60 | Low Temp CS | 45 | B564 UNS N04400 | Ni-Alloy |
| 21 | ASTM A350 LF2 | Low Temp CS | 46 | B564 UNS N6600 | Ni-Alloy |
| 22 | ASTM A350 LF3 | Low Temp CS | 47 | B564 UNS N06625 | Ni-Alloy |
| 23 | ASTM A350 LF6 | Low Temp CS | 48 | B564 UNS N08367 | Ni-Alloy |
| C.Duplex | 49 | B564 UNS N08800 | Ni-Alloy | ||
| 24 | ASTM A182 F51 | Duplex SS | 50 | B564 UNS N08825 | Ni-Alloy |
| 25 | ASTM A182 F60 | Duplex SS | 51 | B564 UNS N10276 | Ni-Alloy |
| 26 | ASTM A182 F53 | Duplex SS | 52 | ASTMB171 UNS C71520 | Cu-Alloy |
Flange Type:
Weld Neck, Slip On, Blind, Plate, Thread, Socket Weld, Lap Joint, Ring Joint, Orifice Flange, Spectacle Blind, Paddle Spacer and Blank Flange, Figure 8 Flange, etc;
Face: Raised Face (RF),Flat Face(FF), Ring Joint (RTJ)
Material:
Carbon Steel: Q235,20#,A105, ST37.2,C22.8, S235JR,P250GH,A350 LF1,LF2 CL1/CL2 LF3 CL1/CL2, ASTM A694 F42,F46,F48,F50,F52,F56,F60,F65,F70
Stainless Steel: A182 F304/304L, F316/316L, F316H,F316Ti,F321,F44(UNS S31254)
Ally Steel: A182 F1,F5/a,F9,F11,F12,F22,F91
Duplex Steel: A182 F51/UNS S31803,F53/UNS S32750 F55/UNS S3260
Special Alloy: ,C95400,C95500,C95800,Monel400,Inconel 600, Inconel 625, Inconel 800, Inconel 825
Standard:
ASME: ANSI/ASME B 16.5,ASME B16.36,ASME B16.47 Series A(MSS SP-44);ASME B16.47 Series B(API 605),AWWA C207
DIN: Plate(DIN2573,2576,2502),Blind(DIN2527),Loose(DIN2641-2676),Welding-Neck (DIN2627-2638), Threaded (DIN2565 2566 2567) ,Slip-On (DIN86029 86030)
EN: EN1092-1
JIS: JIS B2220
UNI: UNI2253-2278,UNI6083,UNI6084,UNI2280,UNI2281-2286, UNI6091-6097
GOST: GOST12820-80, GOST12821-80
BS: BS 4504,BS10-1962,BS3293-1960
Pressure:
ANSI:Class 75, Class 150, Class 300, Class 600, Class 900, Class 1500, Class 2500
DIN:PN 6,PN 10,PN 16,PN 25,PN 40
EN:PN 6,PN 10,PN 16,PN 25,PN 40
JIS:1K,2K,5K,10K,16K,20K,30K,40K,63K ;
GOST:PN 6,PN 10,PN 16,PN 25,PN 40,PN63,PN100,PN160
BS:TABLE D E
Machining Tolerance: From 0.005mm-0.01mm-0.1mm As Standard.
Machined Surface Quality: Ra 0.8-Ra3.2 according to customer requirements
Production Process:
Forging-Heat Treatment-Machining (rough machining and finish machining)-Drilling-Inspect-Stamp-Packing
Heat Treatment: Solution, N+T (Normalizing + Tempering), Q+T (Quenching + Tempering)
Surface Treatment
Anti-rust Oil, Transparent/Yellow/Black Anti-rust Paint,Zinc,Hot dipped Galvanized.
Usage:
Oil Field, Offshore, Water System, Shipbuilding, Natural Gas, Electric Power, Pipe Projects etc.
| ANSI, ASME, ASA, B16.5 150lb/sq.in. SLIP ON FLANGE RF / FF | ||||||||||
| ø | D | b | g | m | J | h | k | Holes | l | Kg. |
| 1/2" | 88,9 | 11,1 | 34,9 | 30,2 | 22,3 | 15,9 | 60,3 | 4 | 15,9 | 0,400 |
| 3/4" | 98,4 | 12,7 | 42,9 | 38,1 | 27,7 | 15,9 | 69,8 | 4 | 15,9 | 0,700 |
| 1" | 107,9 | 14,3 | 50,8 | 49,2 | 34,5 | 17,5 | 79,4 | 4 | 15,9 | 0,800 |
| 1 1/4" | 117,5 | 15,9 | 63,5 | 58,8 | 43,2 | 20,6 | 88,9 | 4 | 15,9 | 1,100 |
| 1 1/2" | 127,0 | 17,5 | 73,0 | 65,1 | 49,5 | 22,2 | 98,4 | 4 | 15,9 | 1,400 |
| 2" | 152,4 | 19,0 | 92,1 | 77,8 | 62,0 | 25,4 | 120,6 | 4 | 19,0 | 2,200 |
| 2 1/2" | 177,8 | 22,2 | 104,8 | 90,5 | 74,7 | 28,6 | 139,7 | 4 | 19,0 | 3,600 |
| 3" | 190,5 | 23,8 | 127,0 | 107,9 | 90,7 | 30,2 | 152,4 | 4 | 19,0 | 4,100 |
| 3 1/2" | 215,9 | 23,8 | 139,7 | 122,2 | 103,4 | 31,7 | 177,8 | 8 | 19,0 | 5,200 |
| 4" | 228,6 | 23,8 | 157,2 | 134,9 | 116,1 | 33,3 | 190,5 | 8 | 19,0 | 5,600 |
| 5" | 254,0 | 23,8 | 185,7 | 163,6 | 143,8 | 36,5 | 215,9 | 8 | 22,2 | 6,300 |
| 6" | 279,4 | 25,4 | 215,9 | 192,1 | 170,7 | 39,7 | 241,3 | 8 | 22,2 | 7,500 |
| 8" | 342,9 | 28,6 | 269,9 | 246,1 | 221,5 | 44,4 | 298,4 | 8 | 22,2 | 12,600 |
| 10" | 406,4 | 30,2 | 323,8 | 304,8 | 276,3 | 49,2 | 361,9 | 12 | 25,4 | 18,500 |
| 12" | 482,6 | 31,7 | 381,0 | 365,1 | 327,1 | 55,6 | 431,8 | 12 | 25,5 | 28,000 |
| 14" | 533,4 | 34,9 | 412,7 | 400,0 | 359,1 | 57,1 | 476,2 | 12 | 28,6 | 36,000 |
| 16" | 596,9 | 36,5 | 469,9 | 457,2 | 410,5 | 63,5 | 539,7 | 16 | 28,6 | 46,000 |
| 18" | 635,0 | 39,7 | 533,4 | 504,8 | 461,8 | 68,3 | 577,8 | 16 | 31,7 | 50,000 |
| 20" | 698,5 | 42,9 | 584,2 | 558,8 | 513,1 | 73,0 | 635,0 | 20 | 31,7 | 64,000 |
| 22" | 749,3 | 46,0 | 641,2 | 609,6 | 564,4 | 79,4 | 692,1 | 20 | 34,9 | 72,000 |
| 24" | 812,8 | 47,6 | 692,1 | 663,6 | 615,9 | 82,5 | 749,3 | 20 | 34,9 | 89,000 |
| NOTE: 1. Class 150 flanges except Lap Joint will be furnished with 0.06 (1.6mm) raised face, which is included in 'Thickness' (C) and 'Length through Hub' (Y1), (Y3). 2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees. 3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub. 4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C). 5. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer's option. |
| ANSI, ASME, ASA, B16.5 300lb/sq.in. SLIP ON FLANGE RF / FF | ||||||||||
| ø | D | b | g | m | J | h | k | Holes | l | Kg. |
| 1/2" | 95,6 | 14,3 | 34,9 | 38,1 | 22,3 | 22,2 | 66,7 | 4 | 15,9 | 0,700 |
| 3/4" | 117,5 | 15,9 | 42,9 | 47,6 | 27,7 | 25,4 | 82,5 | 4 | 19,0 | 1,100 |
| 1" | 123,8 | 17,5 | 50,8 | 54,0 | 34,5 | 27,0 | 88,9 | 4 | 19,0 | 1,400 |
| 1 1/4" | 133,3 | 19,0 | 63,5 | 63,5 | 43,2 | 27,0 | 98,4 | 4 | 19,0 | 1,800 |
| 1 1/2" | 155,6 | 20,6 | 73,0 | 69,8 | 49,5 | 30,2 | 114,3 | 4 | 22,2 | 2,600 |
| 2" | 165,1 | 22,2 | 92,1 | 84,1 | 62,0 | 33,3 | 127,0 | 8 | 19,0 | 3,400 |
| 2 1/2" | 190,5 | 25,4 | 104,8 | 100,0 | 74,7 | 38,1 | 149,2 | 8 | 22,2 | 4,400 |
| 3" | 209,5 | 28,6 | 127,0 | 117,5 | 90,7 | 42,9 | 168,3 | 8 | 22,2 | 6,100 |
| 3 1/2" | 228,6 | 30,2 | 139,7 | 133,3 | 103,4 | 44,4 | 184,1 | 8 | 22,2 | 7,500 |
| 4" | 254,0 | 31,7 | 157,2 | 146,0 | 116,1 | 47,6 | 200,0 | 8 | 22,2 | 10,100 |
| 5" | 279,4 | 34,9 | 185,7 | 177,8 | 143,8 | 50,8 | 234,9 | 8 | 22,2 | 12,500 |
| 6" | 317,5 | 36,5 | 215,9 | 206,4 | 170,7 | 52,4 | 269,9 | 12 | 22,2 | 14,100 |
| 8" | 381,0 | 41,3 | 269,9 | 260,3 | 221,5 | 61,9 | 330,2 | 12 | 25,4 | 24,800 |
| 10" | 444,5 | 47,6 | 323,8 | 320,7 | 276,3 | 66,7 | 387,3 | 16 | 28,6 | 37,100 |
| 12" | 520,7 | 50,8 | 381,0 | 374,6 | 327,1 | 73,0 | 450,8 | 16 | 31,7 | 50,000 |
| 14" | 584,2 | 54,0 | 412,7 | 425,4 | 359,1 | 76,2 | 514,3 | 20 | 31,7 | 70,000 |
| 16" | 647,7 | 57,1 | 469,9 | 482,6 | 410,5 | 82,5 | 571,5 | 20 | 34,9 | 90,000 |
| 18" | 711,2 | 60,3 | 533,4 | 533,4 | 461,8 | 88,9 | 628,6 | 24 | 34,9 | 112,000 |
| 20" | 774,7 | 63,5 | 584,2 | 584,2 | 513,1 | 95,2 | 685,8 | 24 | 34,9 | 133,000 |
| 22" | 838,2 | 66,7 | 641,2 | 641,2 | 564,4 | 101,6 | 742,9 | 24 | 41,3 | 197,000 |
| 24" | 914,4 | 69,8 | 692,1 | 701,7 | 615,9 | 106,4 | 812,8 | 24 | 41,3 | 208,000 |
| NOTE: 1. Class 300 flanges except Lap Joint will be furnished with 0.06 (1.6mm) raised face, which is included in 'Thickness' (C) and 'Length through Hub' (Y1), (Y3). 2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees. 3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub. 4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C). 5. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer's option. |
| ANSI, ASME, ASA, B16.5 600lb/sq.in. Flange SLIP ON FLANGE RF/ FF | ||||||||||
| ø | D | b | g | m | J | h | k | Holes | l | Kg. |
| 1/2" | 95,2 | 14,3 | 34,9 | 38,1 | 22,3 | 22,2 | 66,7 | 4 | 15,9 | 0,800 |
| 3/4" | 117,5 | 15,9 | 42,9 | 47,6 | 27,7 | 25,4 | 82,5 | 4 | 19,0 | 1,400 |
| 1" | 123,8 | 17,5 | 50,8 | 54,0 | 34,5 | 27,0 | 88,9 | 4 | 19,0 | 1,600 |
| 1 1/4" | 133,3 | 20,6 | 63,5 | 63,5 | 43,2 | 28,6 | 98,4 | 4 | 19,0 | 2,100 |
| 1 1/2" | 155,6 | 22,2 | 73,0 | 69,8 | 49,5 | 31,7 | 114,3 | 4 | 22,2 | 3,100 |
| 2" | 165,1 | 25,4 | 92,1 | 84,1 | 62,0 | 36,5 | 127,0 | 8 | 19,0 | 3,700 |
| 2 1/2" | 190,5 | 28,6 | 104,8 | 100,0 | 74,7 | 41,3 | 149,2 | 8 | 22,2 | 5,400 |
| 3" | 209,5 | 31,7 | 127,0 | 117,5 | 90,7 | 46,0 | 168,3 | 8 | 22,2 | 7,300 |
| 3 1/2" | 228,6 | 34,9 | 139,7 | 133,3 | 103,4 | 49,2 | 184,1 | 8 | 25,4 | 8,900 |
| 4" | 273,0 | 38,1 | 157,2 | 152,4 | 116,1 | 54,0 | 215,9 | 8 | 25,4 | 11,800 |
| 5" | 330,2 | 44,4 | 185,7 | 188,9 | 143,8 | 60,3 | 266,7 | 8 | 28,6 | 24,500 |
| 6" | 355,6 | 47,6 | 215,9 | 222,2 | 170,7 | 66,7 | 292,1 | 12 | 28,6 | 29,500 |
| 8" | 419,1 | 55,6 | 269,9 | 273,0 | 221,5 | 76,2 | 349,2 | 12 | 31,7 | 43,000 |
| 10" | 508,0 | 63,5 | 323,8 | 342,8 | 276,3 | 85,7 | 431,8 | 16 | 34,9 | 70,000 |
| 12" | 558,8 | 66,7 | 381,0 | 400,0 | 327,1 | 92,1 | 488,9 | 20 | 34,9 | 86,000 |
| 14" | 603,2 | 69,8 | 412,7 | 431,8 | 359,1 | 93,7 | 527,0 | 20 | 38,1 | 100,000 |
| 16" | 685,8 | 76,2 | 469,9 | 495,3 | 410,5 | 106,4 | 603,2 | 20 | 41,3 | 142,000 |
| 18" | 742,9 | 82,5 | 533,4 | 546,1 | 461,8 | 117,5 | 654,0 | 20 | 44,4 | 175,000 |
| 20" | 812,8 | 88,9 | 584,2 | 609,6 | 513,1 | 127,0 | 723,9 | 24 | 44,4 | 232,000 |
| 22" | 869,9 | 95,2 | 641,2 | 666,7 | 564,4 | 133,3 | 777,9 | 24 | 47,6 | 292,000 |
| 24" | 939,8 | 101,6 | 692,1 | 717,5 | 615,9 | 139,7 | 838,2 | 24 | 50,8 | 330,000 |
| NOTE: 1. Class 600 flanges except Lap Joint will be furnished with 0.25 (6.35mm) raised face, which is not included in 'Thickness' (C) and 'Length through Hub' (Y1), (Y3). 2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees. 3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub. 4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C). 5. Dimensions of sizes 1/2 through 3 1/2 are the same as for Class 400 Flanges. 6. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer's option. |
| Why Choose us? |
| 1. Factory: |
| AEA VALVE, a specialist manufacturer, established since 2008 and professional production of industrial valves over 10 years. |
| 2. Regional Sale: |
| We provide specialized sales service refers to different kind of region all over the world. Each sales team member is good at the local language and well experienced to the responsible market. For example: Russian, German, Spanish, Japanese, etc. |
| 3. Low MOQ: |
| Our factory owns the casting company by itself. We are always ready for providing the sample and producing some small orders, in order to meet the business well. |
| 4. OEM or Customize: |
| OEM Service or Customized size is Available. |
| 5. We can make the products with the client's demand standard or the custom requirement. |
| 6. Complete Solution: |
| We are always ready to hear from you, be responding to your enquiry immediately. Our trade manager is always online for you. |
| 7. High Quality: |
| We have strict quality control system and amounts of testing equipments for different kind of valve, such as size, pressure, working environment etc. We are winning the market reputation with the time goes by. |
| 8. Quick Delivery: |
| We have the large stock for some hot products. |
| 9. Competitive Price: |
| 10. We are the manufacturing company which not only has our own manufacturing workshop, but the casting company as well. We provide the straight factory price and service to our customer. |
| 11. Quality control: |
| All the products are calibrated with real working condition, and tested before shipping as qualified product. |
| 12. Problem solve: |
| If you can't solve the problem in your local, please delivery the product to us, we will repair it and then back to you. |
| 13. Integrity: All the warranty and guarantee from us will be put into come true |
| 14.Online Service: any inquiry, please contact with email: . We will reply you within 12 hours. |